directory structure cleanup
This commit is contained in:
1 parent
c7727d4f0f
commit
c30d4b31c9
75 files changed
+45
-45
No files matched your search
@@ -0,0 +1,123 @@
|
||||
;; Receive a byte from the IEC bus.
|
||||
;; Implemented based on https://www.pagetable.com/?p=1135, https://github.com/mist64/cbmbus_doc,
|
||||
;; http://www.zimmers.net/anonftp/pub/cbm/programming/serial-bus.pdf (page 11)
|
||||
|
||||
iec_rx_byte:
|
||||
|
||||
;; Timing is critical here - execute on disabled IRQs
|
||||
php
|
||||
sei
|
||||
|
||||
;; First, we wait for the talker to release the CLK line
|
||||
jsr iec_wait_for_clk_release
|
||||
|
||||
;; We then release the DATA to signal we are ready
|
||||
;; We can use this routine, since we weren't pulling CLK anyway
|
||||
jsr iec_release_clk_data
|
||||
|
||||
;; Wait till data line is released (someone else might be holding it)
|
||||
jsr iec_wait_for_data_release
|
||||
|
||||
;; Wait for talker to pull CLK.
|
||||
;; If over 200 usec (205 cycles on NTSC machine) , then it is EOI.
|
||||
;; Loop iteraction takes 13 cycles, 17 full iterations are enough
|
||||
|
||||
ldx #$11 ; 2 cycles
|
||||
iec_rx_clk_wait1:
|
||||
lda CIA2_PRA ; 4 cycles
|
||||
rol ; 2 cycles, to put CLK in as the last bit
|
||||
bpl iec_rx_not_eoi ; 2 cycles if not jumped
|
||||
dex ; 2 cycles
|
||||
bne iec_rx_clk_wait1 ; 3 cycles if jumped
|
||||
|
||||
;; Timeout - either this is the last byte of stream, or the stream is empty at all.
|
||||
;; Mark end of stream in IOSTATUS
|
||||
jsr kernalstatus_EOI
|
||||
|
||||
iec_rx_not_empty:
|
||||
|
||||
;; Pull data for 60 usec to confirm it
|
||||
jsr iec_release_clk_pull_data
|
||||
jsr iec_wait60us
|
||||
jsr iec_release_clk_data
|
||||
|
||||
iec_rx_not_eoi:
|
||||
|
||||
;; Latch input bits in on rising edge of CLK, eight times for eight bits.
|
||||
ldx #7
|
||||
|
||||
;; Get empty byte to load into.
|
||||
lda #$00
|
||||
pha
|
||||
|
||||
iec_rx_bit_loop:
|
||||
|
||||
;; Wait for CLK to release
|
||||
jsr iec_wait_for_clk_release
|
||||
|
||||
;; (we do this implicitly below, with a tighter routine,
|
||||
;; so that we don't have timing problems, as the requirements
|
||||
;; are quite tight. Basically we need to read the clock and data
|
||||
;; bit from the same byte read.
|
||||
|
||||
;; DATA now has the next bit, but inverted (well, except that it turns out not to be).
|
||||
;; DATA is in bit 7, which is a bit annoying.
|
||||
;; But we can clock it out with a ROL instruction
|
||||
;; so that it is in C. We can then ROR it into the
|
||||
;; partial data byte.
|
||||
;; We use ROR so that we shift in from the top, so that
|
||||
;; the first bit we shift in ends up in bit 0 after all
|
||||
;; 8 bits have been read.
|
||||
;; ODD: For some reason we don't need to invert the
|
||||
;; received bits. This is weird, because we invert them
|
||||
;; on the way out, and everything in the protocol seems
|
||||
;; to indicate that we sould do so. But experimentation
|
||||
;; has confirmed the bits don't need inversion on reception.
|
||||
|
||||
;; Move data bit into C flag, and loop until bit 6 clears
|
||||
;; i.e., the clock has been released.
|
||||
|
||||
* lda CIA2_PRA
|
||||
rol
|
||||
bpl -
|
||||
|
||||
;; Pull it into the data byte
|
||||
pla
|
||||
ror
|
||||
pha
|
||||
|
||||
;; Wait for CLK to be pulled again, over 300 usec (307 cycles on NTSC)
|
||||
;; consider this a timeout
|
||||
ldy #$19 ; 2 cycles
|
||||
iec_rx_clk_wait2:
|
||||
lda CIA2_PRA ; 4 cycles
|
||||
rol ; 2 cycles, to put CLK in as the last bit
|
||||
bpl + ; 2 cycles if not jumped
|
||||
dey ; 2 cycles
|
||||
bne iec_rx_clk_wait2 ; 3 cycles if jumped
|
||||
|
||||
;; Timeout
|
||||
jsr kernalstatus_EOI
|
||||
pla
|
||||
plp
|
||||
sec ; XXX confirm that sec is really a way to report timeout here
|
||||
rts
|
||||
*
|
||||
;; More bits?
|
||||
dex
|
||||
bpl iec_rx_bit_loop
|
||||
|
||||
;; Then we must within 1000 usec acknowledge the frame by
|
||||
;; pulling DATA. At this point, CLK is pulled by the
|
||||
;; talker and DATA by us, i.e., we are ready to receive
|
||||
;; the next byte. (p11).
|
||||
jsr iec_release_clk_pull_data
|
||||
|
||||
;; Retreive the received byte
|
||||
pla
|
||||
|
||||
;; Return no-error
|
||||
plp
|
||||
clc
|
||||
rts
|
||||
|
||||
Reference in new issue
Block a user