// // JiffyDOS protocol support for IEC // // XXX finish this #if CONFIG_IEC_JIFFYDOS // JiffyDOS timing regime is very strict - before transmitting anything // we need to disable sprites and (if screen is not disabled) wait for // appropriate moment, so that no badline interruption can happen iec_tx_byte_jiffydos: // We need to preserve 3 lowest bits of CIA2_PRA - as they encode // Use C3PO for this, as afterwards we have to set there 0 nevertheless lda CIA2_PRA and #%00000111 sta C3PO // Hide sprites, store their previous status on stack jsr jiffydos_hide_sprites pha // Prepare nibbles to send lda TBTCNT and #$0F tax lda iec_jiffydos_bittable, X // low nibble has to be encoded pha lda TBTCNT and #$F0 pha // Wait till receiver is ready jsr iec_wait_for_data_release __jd_check1: // Wait till it is safe to send data jsr jiffydos_wait_line // Notify device that we are going to send byte by releasing everything // Cycles: 3 + 4 = 7 lda C3PO sta CIA2_PRA // Send high nibble; cycles: 4 + 3 + 4 + 2 + 2 + 2 + 4 = 21 pla // retrieve high nibble from stack ora C3PO // restore VIC-II and RS-232 bits sta CIA2_PRA // bits 4 and 5 on CLK/DATA ror // move bits 6 and 7 to positions 4 and 5 ror and #%00110000 // clear everything but CLK/DATA sta CIA2_PRA // bits 6 and 7 on CLK/DATA // Send low nibble; cycles: 4 + 3 + 4 + 2 + 2 + 2 + 4 = 21 pla // retrieve low nibble from stack ora C3PO // restore VIC-II and RS-232 bits sta CIA2_PRA ror ror and #%00110000 // clear everything but CLK/DATA sta CIA2_PRA // XXX EOI signalled by early CLK (20us delay for non-CLK?) // Re-enable sprites pla lda VIC_SPENA // Mark TX buffer as empty lda #$00 sta C3PO rts iec_rx_byte_jiffydos: // Hide sprites, store their previous status on stack jsr jiffydos_hide_sprites pha // Wait until device is ready to send jsr iec_wait_for_clk_release // Prepare 'start sending' message lda CIA2_PRA and #$FF - BIT_CIA2_PRA_DAT_OUT // release pha // Wait for appropriate moment jsr jiffydos_wait_line // Ask device to start sending bits pla sta CIA2_PRA // XXX retrieve byte // Re-enable sprites pla lda VIC_SPENA rts jiffydos_wait_line: lda VIC_SCROLY and #$10 beq jiffydos_wait_line_done // screen is disabled, no need to watch for badlines // To give the transfer routine as much time as possible, // wait till a badline // XXX this is probably overkill, most likely it is enough to avoid 2 (3?) lines // before badline - to be adjusted in the future !: sec lda VIC_SCROLY sbc VIC_RASTER and #$07 // we want 8 lowest bits bne !- jiffydos_wait_line_done: rts __jd_check2: jiffydos_hide_sprites: lda VIC_SPENA ldx #$00 stx VIC_SPENA rts .function SAME_PAGE_CHECK(label_1, label_2) { #if PASS_SIZETEST .return (label_1 - label_1 % 256) == (label_2 - label_2 % 256) #else .return true #endif } .if (!SAME_PAGE_CHECK(__jd_check1, __jd_check2)) { // To meet the strict JiffyDOS timing, we need to make sure // it does not span across multiple pages, as this would add // 1 cycle to some jump instructions - maybe this wont cause // problems, but better safe than sorry. .error "JiffyDOS code can't span across multiple pages" } #endif // CONFIG_IEC_JIFFYDOS