144 lines
3.4 KiB
ArmAsm
144 lines
3.4 KiB
ArmAsm
|
|
;;
|
|
;; Official Kernal routine, described in:
|
|
;;
|
|
;; - [RG64] C64 Programmer's Reference Guide - page 286
|
|
;; - [CM64] Compute's Mapping the Commodore 64 - page 231
|
|
;; - IEC reference at http://www.zimmers.net/anonftp/pub/cbm/programming/serial-bus.pdf
|
|
;;
|
|
;; CPU registers that has to be preserved (see [RG64]): none
|
|
;;
|
|
|
|
|
|
;; Expects that SETLFS and SETNAM are called before hand.
|
|
;; $YYXX = load address.
|
|
;; (ignored if SETLFS channel = 1, i.e., like ,8,1)
|
|
;; If A=1 then VERIFY instead of LOAD.
|
|
;; On exit, $YYXX is the highest address into which data
|
|
;; will have been placed.
|
|
|
|
;; XXX honor MSGFLG bit 6
|
|
;; XXX add VERIFY support
|
|
|
|
load:
|
|
|
|
;; Are we loading or verifying?
|
|
sta VERCK
|
|
|
|
;; Store start address of LOAD
|
|
stx STAL+0
|
|
sty STAL+1
|
|
|
|
;; Reset status
|
|
jsr kernalstatus_reset
|
|
|
|
;; We need our helpers to get to filenames under ROMs or IO area
|
|
jsr install_ram_routines
|
|
|
|
;; Allow platform-specific routine to takeover the flow
|
|
`TARGET_HOOK_LOAD
|
|
|
|
;; Check whether we support the requested device
|
|
lda current_device_number
|
|
and #$FC
|
|
beq lvs_illegal_device_number ; device number below 4, not an IEC device
|
|
|
|
;; Device numbers above 30 are also illegal (see https://www.pagetable.com/?p=1031),
|
|
;; as the protocol combines device number with command code int one byte,
|
|
;; above 30 it is no longer possible (UNLISTEN and UNTALK codes prevent using
|
|
;; number 31), yet original ROMs show ILLEGAL DEVICE NUMBER error only
|
|
;; for devices 0-3; in our implementation LISTEN / TALK will cause device
|
|
;; not present detected for numbers above 30
|
|
|
|
;; Display SEARCHING FOR + filename
|
|
jsr lvs_display_searching_for
|
|
|
|
;; http://www.zimmers.net/anonftp/pub/cbm/programming/serial-bus.pdf
|
|
;; p13, 16; also p16 tells us this routine doesn't mess with the file table
|
|
;; in the C64, only in the drive.
|
|
|
|
;; Call device to LISTEN (p16)
|
|
lda current_device_number
|
|
jsr listen
|
|
bcs lvs_device_not_found_error
|
|
|
|
;; Open channel 0 (reserved for file reading)
|
|
lda #$00
|
|
jsr iec_cmd_open
|
|
bcs lvs_load_verify_error
|
|
|
|
;; Send file name
|
|
jsr lvs_send_file_name
|
|
bcs lvs_load_verify_error
|
|
|
|
;; Now command device to talk (p16)
|
|
lda current_device_number
|
|
jsr talk
|
|
bcs lvs_load_verify_error
|
|
|
|
lda #$60 ; open channel / data (p3) , required according to p13
|
|
sta IEC_TMP2
|
|
jsr iec_tx_command
|
|
bcs lvs_load_verify_error
|
|
|
|
;; We are currently talker, so do the IEC turn around so that we
|
|
;; are the listener (p16)
|
|
jsr iec_turnaround_to_listen
|
|
bcs lvs_load_verify_error
|
|
|
|
;; Get load address and store it if secondary address is zero
|
|
jsr iec_rx_byte
|
|
bcs lvs_file_not_found_error
|
|
ldx current_secondary_address
|
|
beq +
|
|
sta STAL+0
|
|
*
|
|
jsr iec_rx_byte
|
|
bcs lvs_file_not_found_error
|
|
ldx current_secondary_address
|
|
beq +
|
|
sta STAL+1
|
|
*
|
|
;; Display start address
|
|
jsr lvs_display_loading_verifying
|
|
|
|
load_loop:
|
|
;; We are now ready to receive bytes
|
|
jsr iec_rx_byte
|
|
bcs lvs_load_verify_error
|
|
|
|
;; Handle the byte (store in memory / verify)
|
|
jsr lvs_handle_byte_load_verify
|
|
bcs lvs_load_verify_error
|
|
|
|
;; Advance pointer to data
|
|
jsr lvs_advance_pointer
|
|
bcs lvs_wrap_around_error
|
|
|
|
;; Check for EOI - if so, this was the last byte
|
|
lda IOSTATUS
|
|
and #K_STS_EOI
|
|
beq load_loop
|
|
|
|
;; Display end address
|
|
jsr lvs_display_done
|
|
|
|
;; Close file on drive
|
|
|
|
;; Command drive to stop talking and to close the file
|
|
jsr untlk
|
|
|
|
lda current_device_number
|
|
jsr listen
|
|
|
|
lda #$E0
|
|
sta IEC_TMP2
|
|
jsr iec_tx_command
|
|
jsr iec_tx_command_finalize
|
|
|
|
;; Tell drive to unlisten
|
|
jsr unlsn
|
|
|
|
;; Return last address
|
|
jmp lvs_return_last_address
|