118 lines
3.2 KiB
ArmAsm
118 lines
3.2 KiB
ArmAsm
;; Receive a byte from the IEC bus.
|
|
;; Implemented based on https://www.pagetable.com/?p=1135, https://github.com/mist64/cbmbus_doc,
|
|
;; http://www.zimmers.net/anonftp/pub/cbm/programming/serial-bus.pdf (page 11)
|
|
|
|
iec_rx_byte:
|
|
|
|
;; First, we wait for the talker to release the CLK line
|
|
jsr iec_wait_for_clk_release
|
|
|
|
;; We then release the DATA to signal we are ready
|
|
;; We can use this routine, since we weren't pulling CLK anyway
|
|
jsr iec_release_clk_data
|
|
|
|
;; Wait till data line is released (someone else might be holding it)
|
|
jsr iec_wait_for_data_release
|
|
|
|
;; Wait for talker to pull CLK.
|
|
;; If over 200 usec (205 cycles on NTSC machine) , then it is EOI.
|
|
;; Loop iteraction takes 13 cycles, 17 full iterations are enough
|
|
|
|
ldx #$11 ; 2 cycles
|
|
iec_rx_clk_wait:
|
|
lda CI2PRA ; 4 cycles
|
|
rol ; 2 cycles, to put BIT_CI2PRA_CLK_IN as the last bit
|
|
bpl iec_rx_not_eoi ; 2 cycles if not jumped
|
|
dex ; 2 cycles
|
|
bne iec_rx_clk_wait ; 3 cycles if jumped
|
|
|
|
;; Timeout - wait a little bit more to see if EOI confirmation is needed
|
|
;; (if CLK not pulled within 256 usec - it's not needed, see
|
|
;; https://www.pagetable.com/?p=1135, chapters End of Stream and Empty Stream)
|
|
jsr iec_wait60us
|
|
lda CI2PRA
|
|
rol
|
|
bmi iec_rx_set_eoi
|
|
|
|
jsr iec_rx_set_eoi
|
|
|
|
;; Pull data for 60 usec to confirm
|
|
jsr iec_release_clk_pull_data
|
|
jsr iec_wait60us
|
|
jsr iec_release_clk_data
|
|
|
|
iec_rx_not_eoi:
|
|
|
|
;; Latch input bits in on rising edge of CLK, eight times for eight bits.
|
|
ldx #7
|
|
|
|
;; Get empty byte to load into.
|
|
lda #$00
|
|
pha
|
|
|
|
iec_rx_bit_loop:
|
|
|
|
;; Wait for CLK to release
|
|
jsr iec_wait_for_clk_release
|
|
|
|
;; (we do this implicitly below, with a tighter routine,
|
|
;; so that we don't have timing problems, as the requirements
|
|
;; are quite tight. Basically we need to read the clock and data
|
|
;; bit from the same byte read.
|
|
|
|
;; DATA now has the next bit, but inverted (well, except that it turns out not to be).
|
|
;; DATA is in bit 7, which is a bit annoying.
|
|
;; But we can clock it out with a ROL instruction
|
|
;; so that it is in C. We can then ROR it into the
|
|
;; partial data byte.
|
|
;; We use ROR so that we shift in from the top, so that
|
|
;; the first bit we shift in ends up in bit 0 after all
|
|
;; 8 bits have been read.
|
|
;; ODD: For some reason we don't need to invert the
|
|
;; received bits. This is weird, because we invert them
|
|
;; on the way out, and everything in the protocol seems
|
|
;; to indicate that we sould do so. But experimentation
|
|
;; has confirmed the bits don't need inversion on reception.
|
|
|
|
;; Move data bit into C flag, and loop until bit 6 clears
|
|
;; i.e., the clock has been released.
|
|
|
|
* lda CI2PRA
|
|
rol
|
|
bpl -
|
|
|
|
;; Pull it into the data byte
|
|
pla
|
|
ror
|
|
pha
|
|
|
|
;; Wait for CLK to be pulled again
|
|
jsr iec_wait_for_clk_pull
|
|
|
|
;; More bits?
|
|
dex
|
|
bpl iec_rx_bit_loop
|
|
|
|
;; Then we must within 1000 usec acknowledge the frame by
|
|
;; pulling DATA. At this point, CLK is pulled by the
|
|
;; talker and DATA by us, i.e., we are ready to receive
|
|
;; the next byte. (p11).
|
|
jsr iec_release_clk_pull_data
|
|
|
|
;; Retreive the received byte
|
|
pla
|
|
|
|
;; Return no-error
|
|
clc
|
|
rts
|
|
|
|
iec_rx_set_eoi:
|
|
|
|
;; Store EOI information in IOSTATUS
|
|
lda IOSTATUS
|
|
ora #$40
|
|
sta IOSTATUS
|
|
|
|
clc
|
|
rts
|