improved JiffyDOS optimized LOAD loop

CONFIG.md

@@ -91,9 +91,9 @@ Planned for the future - not available yet.
 
 ### `CONFIG_MEMORY_MODEL_60K`
 
-Uses RAM under BASIC, I/O and KERNAL, takes over `$C000`-`$CFFF` area requires special helper routines installed in `$2A7`-`$2FF` area (normally unused and free for the user). Gives the most free memory for BASIC programs, but it's the slowest and the least compatible model.
+Uses RAM under BASIC, I/O and KERNAL, takes over `$C000`-`$CFFF` area requires special helper routines installed in `$2A7`-`$2FF` area (normally unused and free for the user). Gives the most free memory for BASIC programs, but it's the slowest (for example, forces disabling optimized LOAD loop for JiffyDOS) and the least compatible model.
 
-Comparing to standard memoryy model, it needs about 180 bytes in BASIC segment and 80 bytes in KERNAL segment - at the moment of doing the test, these values are expected to change often.
+Comparing to standard memory model, it needs about 180 bytes in BASIC segment and 80 bytes in KERNAL segment - at the moment of doing the test, these values are expected to change often.
 
 ## I/O devices
 
@@ -107,7 +107,7 @@ Needs over 1000 bytes in KERNAL segment. If unsure - enable.
 
 Adds support for JiffyDOS fast protocol to the IEC bus.
 
-Needs about 420 bytes in KERNAL segment. If unsure - enable.
+Needs about 430 bytes in KERNAL segment. If unsure - enable.
 
 ### `CONFIG_TAPE_TURBO`
 

c64/kernal/iec/load_iec.s

@@ -87,7 +87,7 @@ load_iec:
 	// Display start address
 	jsr lvs_display_loading_verifying
 
-#if CONFIG_IEC_JIFFYDOS
+#if CONFIG_IEC_JIFFYDOS && !CONFIG_MEMORY_MODEL_60K
 
 	// If feasible, use JiffyDOS optimized LOAD loop
 

c64/kernal/iec_fast/load_jiffydos.s

@@ -4,10 +4,14 @@
 //
 
 
-#if CONFIG_IEC_JIFFYDOS
+#if CONFIG_IEC_JIFFYDOS && !CONFIG_MEMORY_MODEL_60K
 
 
-	// XXX add RUN/STOP support
+// Note: original JiffyDOS LOAD loop checks for RUN/STOP key every time a sector is read.
+// For simplicity and some space savings, our routine does not check the RUN/STOP key at all;
+// the protocol is fast enough (especiallyy with modern flash mediums) that probably nobody
+// will want to terminate the loading.
+
 
 load_jiffydos:
 
@@ -18,10 +22,8 @@ load_jiffydos:
 	jsr jiffydos_prepare
 	sta TBTCNT
 
-	// XXX For the first iteration load the whole sector minus 2 bytes
-	// XXX (as they are used to store the start address)
-	// XXX ldy #$FB
-	ldy #$00
+	// A trick to shorten EAL update time
+	ldy #$FF
 
 	// FALLTROUGH
 
@@ -55,8 +57,8 @@ load_jiffydos_loop:
 	lsr
 	lsr
 
-	// Wait for the drive, cycles: 2
-	nop
+	// Wait for the drive - we have time to increment offset, cycles: 2
+	iny
 
 	// Get bits, cycles: 4 + 2 + 2 = 8
 	ora CIA2_PRA                       // bits 2 and 3 on CLK/DATA
@@ -74,7 +76,7 @@ load_jiffydos_loop:
 	eor CIA2_PRA                       // bits 6 and 7 on CLK/DATA
 
 	// Store retrieved byte, cycles: 6 
-	sta (EAL),y
+	sta (EAL),y                        // not compatible with CONFIG_MEMORY_MODEL_60K
 
 	// Retrieve status bits, cycles: 4
 	bit CIA2_PRA
@@ -85,16 +87,25 @@ load_jiffydos_loop:
 	// If CLK line not active - this was the last byte
 	bvs load_jiffydos_end
 
-	// Advance pointer to data XXX use INY instead, advance once per sector only
-	jsr lvs_advance_EAL
-
-	jmp load_jiffydos_loop	
+	// Handle EAL
+	cpy #$FF
+	bne load_jiffydos_loop
+	inc EAL+1
+	jmp load_jiffydos_loop
 
 load_jiffydos_end:
 
-	// Save last byyte
+	// Save last byte
 	tax
 
+	// Update EAL
+	tya
+	sec
+	adc EAL+0
+	sta EAL+0
+	bcc !+
+	inc EAL+1
+!:
 	// Indicate that no byte waits in output buffer
 	lda #$00
 	sta C3PO
@@ -107,11 +118,11 @@ load_jiffydos_end:
 	lda TBTCNT
 	sta VIC_SPENA
 
-	// Store last byte as unoptimized LOAD would
+	// Store last byte as unoptimized LOAD routine would
 	stx TBTCNT
 
 	// End of load loop
 	jmp load_iec_loop_end
 
 
-#endif // CONFIG_IEC_JIFFYDOS
+#endif // CONFIG_IEC_JIFFYDOS and not CONFIG_MEMORY_MODEL_60K