143 lines
2.6 KiB
ArmAsm
143 lines
2.6 KiB
ArmAsm
|
|
//
|
|
// JiffyDOS protocol support for IEC
|
|
//
|
|
|
|
// XXX finish this
|
|
|
|
|
|
|
|
#if CONFIG_IEC_JIFFYDOS
|
|
|
|
|
|
// JiffyDOS timing regime is very strict - before transmitting anything
|
|
// we need to disable sprites and (if screen is not disabled) wait for
|
|
// appropriate moment, so that no badline interruption can happen
|
|
|
|
|
|
iec_tx_byte_jiffydos:
|
|
|
|
jsr jiffydos_hide_sprites
|
|
pha // store previous sprite status on stack
|
|
|
|
// XXX prepare bit pairs too send
|
|
|
|
// XXX lda TBTCNT
|
|
// XXX bits to stack: 0, 2
|
|
// XXX bits to stack: 1, 3
|
|
// XXX bits to stack: 7, 6
|
|
// XXX bits to stack: 5, 4
|
|
|
|
jsr jiffydos_wait_line
|
|
|
|
__jd_check1:
|
|
|
|
// XXX send byte
|
|
|
|
|
|
// Re-enable sprites
|
|
pla
|
|
lda VIC_SPENA
|
|
|
|
// XXX reenable screen - temporary, just for testing
|
|
lda VIC_SCROLY
|
|
ora #$10
|
|
sta VIC_SCROLY
|
|
|
|
rts
|
|
|
|
|
|
iec_rx_byte_jiffydos:
|
|
|
|
jsr jiffydos_hide_sprites
|
|
pha // store previous sprite status on stack
|
|
|
|
// Wait until device is ready to send
|
|
jsr iec_wait_for_clk_release
|
|
|
|
// Prepare 'start sending' message
|
|
lda CIA2_PRA
|
|
and #$FF - BIT_CIA2_PRA_DAT_OUT // release
|
|
pha
|
|
|
|
// Wait for appropriate moment
|
|
jsr jiffydos_wait_line
|
|
|
|
// Ask device to start sending bits
|
|
pla
|
|
sta CIA2_PRA
|
|
|
|
|
|
// XXX retrieve byte
|
|
|
|
|
|
// Re-enable sprites
|
|
pla
|
|
lda VIC_SPENA
|
|
|
|
// XXX reenable screen - temporary, just for testing
|
|
tay
|
|
lda VIC_SCROLY
|
|
ora #$10
|
|
sta VIC_SCROLY
|
|
tya
|
|
|
|
rts
|
|
|
|
|
|
jiffydos_wait_line:
|
|
|
|
lda VIC_SCROLY
|
|
and #$10
|
|
beq jiffydos_wait_line_done // screen is disabled, no need to watch for badlines
|
|
|
|
// To give the transfer routine as much time as possible,
|
|
// wait till a badline
|
|
|
|
// XXX this is probably overkill, most likely it is enough to avoid 2 (3?) lines
|
|
// before badline - to be adjusted in the future
|
|
!:
|
|
sec
|
|
lda VIC_SCROLY
|
|
sbc VIC_RASTER
|
|
and #$07 // we want 8 lowest bits
|
|
bne !-
|
|
|
|
jiffydos_wait_line_done:
|
|
rts
|
|
|
|
|
|
__jd_check2:
|
|
|
|
|
|
jiffydos_hide_sprites:
|
|
|
|
lda VIC_SPENA
|
|
ldx #$00
|
|
stx VIC_SPENA
|
|
|
|
rts
|
|
|
|
|
|
.function SAME_PAGE_CHECK(label_1, label_2)
|
|
{
|
|
#if PASS_SIZETEST
|
|
.return (label_1 - label_1 % 256) == (label_2 - label_2 % 256)
|
|
#else
|
|
.return true
|
|
#endif
|
|
}
|
|
|
|
.if (!SAME_PAGE_CHECK(__jd_check1, __jd_check2))
|
|
{
|
|
// To meet the strict JiffyDOS timing, we need to make sure
|
|
// it does not span across multiple pages, as this would add
|
|
// 1 cycle to some jump instructions - maybe this wont cause
|
|
// problems, but better safe than sorry.
|
|
|
|
.error "JiffyDOS code can't span across multiple pages"
|
|
}
|
|
|
|
|
|
#endif // CONFIG_IEC_JIFFYDOS
|